The groove held half the seal
One groove confines only half the section; under compression the seal is pushed out of the mouth and the compression set goes with it.
The arithmetic on an appliance part always lands on the piece price.
Partshousings, panels, handles, bezels
Surfacegloss, matt, fine texture — out of the mould
Costtool amortisation, cycle time, finishing
CustomersOEMs, contract manufacturers, brands
Appliances are one of the harder composite categories. An appearance part wants Class A. A structural part wants thin walls that do not sag. Assembly wants to snap home first time. Safety has to be verified to the customer's standard. All of that is technical, and plenty of people can do it. What is hard is the last step: after the material change, the piece has to land below the price it replaces — or be dearer for a reason the customer can state.
Three kinds of customer: OEMs, contract manufacturers, smaller brands. All three run, and they do not ask the same question. The OEM asks about compliance and consistency. The contract manufacturer asks about piece price and lead time. The smaller brand asks whether the appearance can be delivered with the part.
Outer housings, panels, handles, bezel frames, internal brackets, base load plates, edge trim. Moulds are cut by a partner toolmaker to our specification and we sign them off; cost and ownership are agreed per project.
Custom parts to drawing Finished components and private label Moulding processes
An appliance's appearance part is seen before anything else. Class A rests on three things — the finish of the mould face, the lay-up sequence, the resin content. Not on finishing. A sanded face shows waves under the light, and the light in an appliance showroom is the light that finds them.
Surface texture is set in the mould as well: gloss, matt, fine texture, and 3K or 12K weave. These are the composite's own surfaces, made in the mould face, not sprayed on. Brushed metal is not a composite surface; the two processes do not stand in for each other, and they are quoted separately.
Colour is a separate matter. Colour difference across a batch runs to one colour master and one paint batch. Dark parts are forgiving; light parts are not — the composite reads dark underneath, so a hiding layer goes on first, or the paint goes grey. White parts also turn on yellowing resistance, with resin and clearcoat chosen to the service life.
Where the part sits on the same face as ABS, sheet metal or aluminium, the colour master is made with all of them at once, not one per supplier.
Appliances are a commodity market and the piece price is squeezed hard. A composite part's cost structure is not steel's or ABS's, and the account is kept separately:
Mould amortisation is fixed and thins with volume. Cycle time sets labour and machine occupancy. Finishing — paint, screen print, assembly — is often dearer than the moulding itself. The last of the three is the one most often missed: two coats of paint on one part can double its cost.
Which parts suit a change to composite: the ones carrying an appearance premium (high-end models, visible faces), the ones that have to lose weight (handheld, portable), the ones that should need no paint at all (natural plus clearcoat, forged carbon).
Which do not: high volume, low price, purely internal support parts. ABS or sheet metal is cheaper there, and composite only loses on the quotation.
Compliance documents come with the quote: RoHS and REACH declarations, and a fuller material composition table where the customer needs one.
An appliance housing is squeezed from both sides by cost and by weight, and the user will press it, carry it, stack it.
A thin wall gets its stiffness from structure, not from thickness: local ribs, stepped wall thickness, radii at the corners, local reinforcement around fixing points. Those four are settled at design stage; adding ribs once the mould is cut only means cutting a new mould.
Stacking and transport loads are calculated separately. Appliances travel long distances and are handled several times — three high in a carton, a summer in a container — and under those conditions creep tests the structure harder than a static load does.
Where insulation is needed the wall goes sandwich; where it is not, solid. Two structures in one part, moulded in one shot, which is cheaper than making two and assembling them.
Appliance assembly is held tighter than industrial work. A machine carries dozens of parts, the stack accumulates, and a panel gap that does not line up comes back as a return.
Snap-fits come in two kinds: releasable and permanent. A releasable snap works by elastic deflection, and continuous-fibre composite is much stiffer and far less ductile than engineering plastic. At the same shape the plastic part clicks in; the continuous-fibre one either will not go in, or goes in and cracks — so the geometry is recalculated for the material, and the plastic part's drawing is not copied across. Short-fibre material is a different case: LFT-D and the like can follow the plastic part's logic for a snap. Fibre orientation and weld lines are calculated with it, not just the wall thickness.
Bosses are where it most often goes wrong. Tapping a thread straight into composite cracks under repeated assembly. The right answer is a metal insert moulded in, or a boss wall thickened enough to take the torque.
The tolerance stack is aligned to the customer's assembly datum. Our parts are made to the drawing, but a drawing's tolerance is for one part; once it is on the machine and the stack accumulates, where the gap lands is worked out with the customer, not assumed.
Some appliance parts are not chosen by strength. They are chosen by what touches them. The same kind of housing, on different parts, meets different detergent, hot water, low temperature and oil — so the material is not one material.
Once the duty is fixed, the resin system, the surface layer and the inserts follow. Give the medium, the temperature and the contact time, and material selection has a basis; without them the only safe answer is the most conservative system, and the piece price stays high.
One groove confines only half the section; under compression the seal is pushed out of the mouth and the compression set goes with it.
Water and steam sealing on appliances runs the same way: ask first whether the groove holds the seal, then talk about the seal. Re-selecting the seal means re-validating and re-sampling; cutting the groove fixes it once, in the structure, and costs less.
Why is an appliance part dearer than an injection moulding?
The mould and the finishing. One injection tool runs hundreds of thousands of parts; one composite mould runs thousands to tens of thousands. An appearance part is painted as well, which is more operations than injection moulding. So the change is made for a stated reason — appearance, weight, or no paint.
Can you match the existing colour?
Yes, with the same colour master and the same paint batch. Dark parts are easy; light parts need a hiding layer first, or the composite base shows through.
How does flame retardance work with safety approval?
Flame retardance comes from the resin formulation, not from a coating applied afterwards. The numbers are verified to the customer's standard — we do not set them. We do not sign the safety approval on the customer's behalf.
Can a snap-fit be copied straight from a plastic part?
Not from a continuous-fibre part: it is stiffer and far less ductile, so at the same shape it cracks or fails to hold. The geometry is recalculated. Short-fibre material (LFT-D) can follow the plastic part's logic, with fibre orientation and weld lines calculated as well.
Can you make parts that resist media?
Yes, but the medium, the temperature and the contact time come first. Those three differ, and the material follows them.
Do you take small batches?
Yes. Small batches are proved on soft tooling for appearance and assembly, then move to steel as volume arrives. An appearance tool costs more than a structural one, so it is listed separately in the quote.
Who cuts the mould, and who owns it?
A partner toolmaker cuts it to our specification and we sign it off. Cost and ownership are agreed per project.
Give us the part type, the annual volume and the price you pay now — whether it can change and whether it pays are answered in one go.
Request a quoteA drawing, a photo of a failed part, or three lines of requirement is enough to start. Scope, price indication and lead time within 24 hours.
No commitment · NDA available · Reply within 24 hours