Custom composite parts

Every enquiry answered within 24 hours

Which line your part takes

What the part is Route Where the line stops
Closed three-dimensional shell (an enclosure or housing) — inserts to bury, both faces seen HP-RTM A steel mould and high-pressure injection add up to heavy spend; a shape change is a new mould
Semi-structural part with ribs, bosses and inserts Compression moulding (prepreg or wet) Flow length is limited; a deep cavity and a large flat face are hard to serve together
Body of revolution, closed section Filament winding The surface is mandrel or machined, and will not pass as an appearance face
Section that does not change along its length Pultrusion The section cannot vary; transverse strength is below axial
High volume, high integration, thermoplastic LFT-D Fibre length stops short of continuous; a thin wall over a long flow path is out

The part types we see most are enclosures, housings and box-type parts. They have curvature on the outside, something to fit inside, inserts to bury and a seal face to hold. They go to HP-RTM or compression moulding, and both faces can be delivered as appearance faces. Constant-section tube, rod and profile go to pultrusion; bodies of revolution go to winding.

From drawing to part, all in house

  • Design review whether the part can be made at all, where it cannot, and which single change saves the most. A change on the drawing is cheaper than a change in the tool.
  • Tooling quoted through a toolmaker. You pay for it, you own it, and it leaves with you if you change supplier.
  • Preform fabric cutting, lay-up and preforming in house. The hard part of the shape is a process in its own right, not something thrown in.
  • Forming one of the five lines, chosen per part. Once the line is chosen, everything downstream is scheduled from it.
  • Post-machining cutting, holes, edge milling, contoured cut-outs, end sealing and assembly, all in house. These operations serve our own formed parts only; a part that arrives already made is not taken on.
  • Finish painting and coating in house. Class A takes a polished mould and then a topcoat, and that sequence never leaves the plant; a finish problem does not have to be chased to a third party.
  • Inspection CMM reports, ultrasonic and section microscopy, first-article reports, samples retained with every batch.

What we can show on accuracy and inspection

Cutting ±0.01 mm, hole positions ±0.01 mm, CNC edge milling ±0.2 mm. These three are commitments: they go into the quotation.

Moulding tolerance differs from line to line. Move a part from one line to another and the tolerance moves with it, so it is quoted per part.

What inspection can show: CMM reports; void content and fibre volume fraction by ultrasonic or section microscopy; insert pull-out force; a retained sample from every batch. Where flame retardance is required, a type test can go to a third party.

What we do not take on

  • Finish-machining of a supplied part: no. A part that is already made, brought in to be cut, drilled or trimmed — we do not take that on.
  • Fibre or prepreg that belongs to you: yes. You supply the material, we form it, and the part that comes out is ours to stand behind.
  • Post-machining is for our own parts only. A part off our line, and a machining fault is ours; a part from outside, and it cannot be pinned down.

Tooling, first article and batch

The tool is quoted through a toolmaker; the cost and the ownership are both yours.

The sequence. Tooling is paid for, a sample is made, the sample is signed off, the first production run follows. Volume runs after that first run is signed off. Change the drawing between sample and first run and it is the tool that changes, so it costs more the later it comes.

Batch size is agreed per project; there is no catalogue minimum.

Lead time is agreed per project.

What to send for a firm quote

  • Drawing STEP, IGES, DWG and DXF are all read; PDF works, and a dimensioned sketch is enough to start.
  • Service conditions load direction, temperature, and whether fatigue or impact is in play.
  • Delivery how good the surface has to be, and whether a first-article report is needed.

With all three, the first quote is the quote. Where something is missing we ask — we would rather ask than send a price that comes back for revision.

Automotive interior trim and car parts

A carbon weave on the visible face, an injection-moulded rib structure on the back, made in one shot. No secondary bonding, and no second tool just for the weave. Datum comes from the assembly sequence; the cosmetic face is settled in the tool, not by polishing afterwards.

Parts we have made: carbon fibre interior trim, one part in two materials ; for body structure see composite body panels for vehicles.

Cases

Parts that do not belong in a catalogue

View all case studies

Send the drawing. We will send the route.

A drawing, a photo of a failed part, or three lines of requirement is enough to start. Scope, price indication and lead time within 24 hours.

No commitment · NDA available · Reply within 24 hours

Request a quote WhatsApp