Roll wrapped carbon fibre tube
TubesCarbon fibre
OD 6–500 mm, wall thickness 0.125–10 mm (matched to OD)
Roll wrapping
TubesCarbon fibre
OD 6–500 mm, wall thickness 0.125–10 mm (matched to OD)
Roll wrapping
TubesCarbon fibre
Side 10×10–200×200 mm, wall thickness 1.0–10 mm (matched to side)
Pultrusion
TubesCarbon fibre
Across flats 10–100 mm (hexagon and octagon), wall 1.0–10 mm (matched to A/F)
Pultrusion / roll wrapping / compression moulding
TubesCarbon fibre
Large end 12–150 mm, small end 8–90 mm, taper 1:300 to 1:15
Roll wrapping / filament winding / compression moulding
TubesGlass fibre
Stock range: outside diameter 4–150 mm, wall 1–6 mm
Pultrusion as standard, winding for large diameters, roll wrapping for thin-wall small batches
Made to drawing
Send the drawing or the duty — we will say whether it can be made, and how.
Talk to us
A round tube bends the same in every direction and takes torsion best, telescopic fits, drive shafts and rollers all use it. Square and rectangular tube give you flat faces: easier to bolt, easier to skin a panel onto — which is why frames, gantries and machine enclosures use them. Polygon tube (hex, octagon) replaces round where a joint must not rotate — a wrench bites and does not slip. Tapered tube goes into telescopic sections, masts and any member whose section has to change.
| Section | Size range | Process | Tolerance |
|---|---|---|---|
| Round tube | OD 6–500 mm, wall 0.125–10 mm | Roll wrapping | OD ±0.1 mm, ±0.05 mm ground |
| Square / rectangular | Side 10×10–200×200 mm, wall 1.0–10 mm | Pultrusion | Side ±0.1 mm, 90° ≤0.5° |
| Polygon tube | 10–100 mm across flats (hex, octagon), wall 1.0–10 mm | Pultrusion | Across flats ±0.1 mm (±0.2 mm above 50) |
| Tapered tube | Large end 12–150 mm, small end 8–90 mm, taper 1:300 to 1:15 | Roll wrapping / winding / moulding | To drawing |
Cut to the length you need; Sizes outside the table are made to drawing.
Pultrusion pulls every fibre along the axis: highest axial stiffness, lowest unit price, but the section is fixed by the die. A new size means a new die. Roll wrapping lays prepreg onto a mandrel layer by layer, so the layup angle follows the load: bending and torsion come out more balanced. Thin walls need no tool. Filament winding runs tow onto the mandrel at an angle for the highest hoop strength, which is what pressure parts and large diameters use.
The comparison buyers ask for most is roll wrapped against pultruded. The round tube page sets it out item by item: roll wrapped vs pultruded。
Cutting to length, hole drilling, slotting and end facing are all done in house. Water-jet guided cutting keeps the heat-affected zone small, so the cut edge needs no rework; slots and hole positions hold ±0.01 mm. Where a metal end or flange is involved the part ships as an assembly, with the fit confirmed on the first article — it goes onto your line as delivered. This applies to our own tube only; we do not machine customer-supplied material.
Outside diameter and wall (or inside diameter), length and quantity, and the duty — which way it is loaded, whether it is visible, whether it sees chemicals. Upload a drawing if you have one; without one, the same parameters written out are enough, and lead time and tooling come back in the same reply.
A drawing, a photo of a failed part, or three lines of requirement is enough to start. Scope, price indication and lead time within 24 hours.
No commitment · NDA available · Reply within 24 hours