Reference image. The actual surface and colour depend on the resin and the finish.
Overview
Carbon fibre polygon tube. Hexagonal carbon fibre tube, carbon fibre octagonal tube and other regular polygon sections, formed by pultrusion, roll wrapping or compression moulding. Across flats 10–100 mm and wall thickness 1.0–10 mm on the carbon fibre hexagonal tube; pultruded sections are cut to length. Across flats tolerance ±0.1 mm (±0.2 mm above 50); corner radius determined by the wall thickness. Post-machining available: cutting, hole drilling, slotting, end facing, grinding, bonding and assembly. For a finished part rather than a length of stock, the route is custom composite parts.
Actuators and drive shafts that must not rotate on the shaft
Spanner flats, handwheels and knobs
Robot joints and locating shafts
Telescoping poles and masts
Camera and survey stands
Locating parts in fixtures and jigs
Stock sizes in detail
Read it as across-flats × wall. Across-corners is derived (1.155 × for hex, 1.082 × for octagon) and is not tabulated — measuring across corners overstates it.
Code
Across flats
Inner A/F
Across corners
Wall
Length
Tolerance
Note
HX-10-1.0
10
8
11.5
1.0
1000
±0.1
Knob and handwheel
HX-12-1.0
12
10
13.9
1.0
1000
±0.1
Locating pin shaft
HX-13-1.0
13
11
15.0
1.0
1000
±0.1
Standard socket size
HX-15-1.0
15
13
17.3
1.0
1000
±0.1
Inner telescoping tube
HX-15-1.5
15
12
17.3
1.5
1000
±0.1
Inner telescoping tube
HX-17-1.0
17
15
19.6
1.0
1000
±0.1
Standard socket size
HX-17-1.5
17
14
19.6
1.5
1000
±0.1
Drive shaft
HX-19-1.5
19
16
21.9
1.5
1000
±0.1
Standard socket size
HX-20-1.5
20
17
23.1
1.5
1000
±0.1
Robot joint
HX-22-1.5
22
19
25.4
1.5
1000
±0.1
Actuator
HX-24-1.5
24
21
27.7
1.5
1000
±0.1
Standard socket size
HX-24-2.0
24
20
27.7
2.0
1000
±0.1
Drive shaft
HX-25-1.5
25
22
28.9
1.5
1000
±0.1
Outer telescoping tube
HX-25-2.0
25
21
28.9
2.0
1000
±0.1
Outer telescoping tube
HX-27-2.0
27
23
31.2
2.0
1000
±0.1
Tooling location
HX-30-2.0
30
26
34.6
2.0
1000
±0.1
Standard socket size
HX-30-2.5
30
25
34.6
2.5
1000
±0.1
Robot joint
HX-32-2.0
32
28
37.0
2.0
1000
±0.1
Structural part
HX-36-2.0
36
32
41.6
2.0
1000
±0.1
Standard socket size
HX-36-2.5
36
31
41.6
2.5
1000
±0.1
Mast
HX-40-2.5
40
35
46.2
2.5
1000
±0.1
Mast
HX-46-3.0
46
40
53.1
3.0
1000
±0.1
Standard socket size
HX-50-3.0
50
44
57.7
3.0
1000
±0.1
Drive shaft
HX-60-3.0
60
54
69.3
3.0
1000
±0.2
Structural part
HX-65-4.0
65
57
75.1
4.0
1000
±0.2
Structural part
HX-70-4.0
70
62
80.8
4.0
1000
±0.2
Structural part
HX-80-4.0
80
72
92.4
4.0
1000
±0.2
Large-diameter structure
HX-90-5.0
90
80
103.9
5.0
1000
±0.2
Large-diameter structure
HX-100-5.0
100
90
115.5
5.0
1000
±0.2
To drawing
OC-25-1.5
25
22
27.1
1.5
1000
±0.1
Octagonal tube · indexing plate
OC-40-2.5
40
35
43.3
2.5
1000
±0.1
Octagonal tube · tooling location
OC-60-3.0
60
54
64.9
3.0
1000
±0.2
Octagonal tube · structural part
OC-80-4.0
80
72
86.6
4.0
1000
±0.2
Octagonal tube · to drawing
The table lists stock and regular sections, with A/F sizes set on standard socket sizes (13/17/19/24/30/36/46) so off-the-shelf spanners and clamps fit; the carbon fibre hexagonal tube range covers all of them. Lengths are stock cut lengths — pultruded sections can be supplied cut to length. Side counts and across-flats are made to drawing; MOQ 500 pcs, trial batch negotiable.
Use a hex so you do not need a keyway
A round tube carrying torque has to be locked against rotation: a keyway. A pin, or a clamp collar squeezed tight, each one adds an operation and a failure point. A polygon tube hands the job to the section itself: fit a hex to a hex and the torque goes through. It returns to the same angle after repeated assembly. The number of sides sets the index. A hex indexes at 60°, six positions; an octagon at 45°, eight. Mechanisms that need 45° location, indexing tables, multi-station fixtures, take the octagon. Everything else takes the hex, because standard sockets, spanners and clamps are all made for hex. A carbon fibre hex tube takes off-the-shelf fittings, the cost has to be stated. At the same cross-sectional area, a polygon has lower torsional stiffness than a round tube. The corners are discontinuous and stress concentration sits there. The section suits location and torque transfer, not using a long shaft as a torsion spring. If you need high torsional stiffness and anti-rotation together. A round tube with bonded metal ends is less trouble than forcing a polygon to do both,
Across flats. Across corners and side length: fix the basis first. The error this line makes most often is quoting across corners when the customer asked for across flats. On a hexagon the across-corners figure is 15.5% larger than across flats; on an octagon, 8.2%, enough to stop a part going in. <strong>Width across flats (A/F)</strong> is the distance between two parallel faces. It is the default for quotation, drawing and inspection, and the inner width across flats is that figure less twice the wall thickness. <strong>Width across corners</strong> is the distance between two opposite vertices, and is always the larger of the two. <strong>Side length</strong> is the width of a single face, conversion for a regular hexagon. Across corners = 1.155 × across flats; side length = across flats ÷ 1.732. For a regular octagon: across corners = 1.082 × across flats; side length = across flats ÷ 2.414. A hexagon tube at 17 mm across flats is 19.6 mm across corners. That is exactly the across-corners of an M10 nut, so it drops into the same hole. Across corners is the right figure only when the part has to pass through a round hole, when the inscribed circle is being calculated. When comparing against a bought-in standard part. Everywhere else quote across flats, and mark A/F on the drawing.
A 120° internal angle is easier to form than 90°
A hexagon has an internal angle of 120°, an octagon 135°, a square tube 90°. The wider the angle, the less the prepreg or fibre bundle is squeezed as it passes round the mandrel. The smaller the resin-rich zone left in the corner. At the same wall thickness, then, a polygon tube gets better corner quality than a square tube. Is less likely to crack from the corner. Corner radius is still set by wall thickness: the inner corner radius is the same order as the wall, 1–1.5 mm being normal. The outer corner radius equals the inner radius plus the wall thickness. For a sharper corner, thin the wall or go to machining, neither pultrusion nor compression moulding can produce a zero radius. Number of sides, across flats, A/F tolerance and corner radius are all fixed in one go before the die is cut. Change any one of them and it is a new die.
Pultrusion, roll wrapping or compression moulding — how to choose
Pultrusion: constant section, continuous. All the fibre is axial, so axial stiffness is highest and the unit price lowest. A/F is held by the sizing die; 10–100 mm is the sweet spot, and length is cut to order. The weakness is hoop: an over-tightened clamp collar crushes the side. Roll wrapping: prepreg laid layer by layer on a polygon mandrel, so variable wall thickness and an exposed 3K weave are both possible. A polygon mandrel is harder to demould than a round one. Length is limited by the mandrel, usually 1000–2000 mm, at a higher unit cost. Choose it for carbon weave appearance, or for thin-wall large sections. Compression moulding: short parts, parts with a flange or a formed end, parts with bonded inserts. A forged finish is possible, but unit cost is highest and a die is needed, in one line. Long constant section, pultrude; appearance, roll wrap; structural features, compression mould.
Surface: how the weave is made
The outer fabric sets the pattern, 3K/12K twill is the most common. A woven finish, as European customers call it, plain weave is denser and flatter. UD uses unidirectional cloth and gives an even matte black, which suits parts still to be painted. The weave is fixed by the outer fabric and post-machining cannot change it, so settle it when you order. Roll-wrapped parts can be supplied in 3K/12K twill, plain weave or UD on all stock sections. Pultruded sections are normally UD, and a pattern means going to roll wrapping.
Delivery states
Natural with clear coat Gloss, weave clearly visible; the carbon weave shows as soon as the part is fitted — the default for most visible parts.
Matte The same coating system, flattened; fewer fingerprints and reflections, common on equipment housings and exposed structural parts.
Painted The surface can be painted to customer requirement; colour and final gloss are set per project.
Laser engraving Customer logo, part number or graphic engraved on the surface.
Tolerance and inspection
Across flats (≤50)
±0.1 mm
Calliper + dimensional report
Across flats (>50)
±0.2 mm
Calliper
Across corners
Derived from across flats, not controlled separately
Projector
Wall thickness
±5% (thin wall counted by plies)
Calliper / ultrasonic
Inner corner radius
Determined by the wall thickness (1–1.5 mm)
Profile gauge / projector
Included angle of adjacent faces
≤0.5°
Angle gauge + feeler gauge
Straightness and twist
1 mm / m
Surface plate measurement
Length (cut to length, squareness of the cut end ±0.5°)
±0.1 mm
Water-jet guided / CNC
Hole position and slotting
±0.01 mm
CMM
Common questions
Can you make parts to drawing?
Yes. Water-jet guided cutting to length, hole drilling and slotting, CNC milling and end facing are all done in-house; where a metal end, flange or insert is required, we supply the assembly, with the fit confirmed at first-article stage. We do not cut threads into carbon fibre — connections are bonded or flanged.
Polygon tube or round tube — which should I choose?
Use a polygon where the part must not rotate, and must return to the same angle after being taken apart; use round tube where you need high torsional stiffness, winding, or a sliding fit. Crush resistance in both comes from wall thickness and hoop plies — the difference is the section, not the material
How do across flats and across corners convert?
Hexagon: across corners = 1.155 × across flats; octagon: = 1.082 × across flats. Quote and inspect on across flats; use across corners only when the part has to pass through a hole or when the inscribed circle is being calculated.
Hexagon or octagon — which should I choose?
A hex indexes at 60°, and standard spanners and sockets are made for hex, so fittings are off the shelf. An octagon indexes at 45°, for indexing plates and multi-station fixtures. Hexagon: across corners = 1.155 × across flats; octagon: = 1.082 × across flats. Quote and inspect on across flats; use across corners only when the part has to pass through a hole or when the inscribed circle is being calculated. Hexagon or octagon
Which should I choose?
A hex indexes at 60°, and standard spanners and sockets are made for hex, so fittings are off the shelf; an octagon indexes at 45°, for indexing plates and multi-station fixtures. The more sides there are, the closer the section comes to a round tube, and the weaker its resistance to rotation
Can you make other side counts?
Yes. Pentagons, twelve-sided and irregular sections are made to drawing on a new die, provided the die can be built — an odd number of sides needs a segmented mandrel for demoulding, and cost and lead time are recalculated
What is the difference between pultruded and roll-wrapped polygon tube?
Pultrusion holds A/F firmly, costs less and is cut to order, but is UD only and weak in hoop; roll wrapping gives carbon weave and variable wall thickness, with length limited by the mandrel to 1000–2000 mm and a higher unit cost
What are the MOQ and lead time?
500 pcs for standard across flats; trial batches by negotiation. Normal batches ship in 15–20 days; a new die takes 5–7 days, with irregular and odd-sided sections quoted separately
Can two hexagon tubes telescope, and what clearance?
Yes. Supplied as a pair, with the inner and outer tube matched to a 0.2 mm across-flats clearance. Both halves come from the same production batch, so drift between batches cannot leave a pair that will not fit. The hexagon is already keyed against rotation, so no keyway or pin is needed; where a tighter fit is required, it is matched to drawing
Can you make glass fibre?
Yes, in the same section — lower stiffness and lower cost, common for insulating parts and low-frequency structures. Quoted through the glass fibre product line
Send us the size
Section, length, quantity and service conditions — with these in hand the quote is accurate. Upload a drawing if you have one; without one, the same figures written out will do.
Company addressZhuyuan Tianhuan International, No. 76 Keji 2nd Road, High-tech Zone, Xi'an, Shaanxi, China
FactoryFengjing Industrial Park, Middle Section of Fengwu East Road, Huyi District, Xi'an, Shaanxi, China