Overview

Roll wrapped carbon fibre tube. Prepreg goes onto the mandrel at the layup angle, then cures and is demoulded. Wall thickness and stiffness are matched to the load, with no separate mould needed for thin wall. OD 6–500 mm, wall thickness 0.125–10 mm, cut to length. OD tolerance ±0.1 mm, ±0.05 mm when ground, slotting and hole positions ±0.01 mm. Post-machining available: cutting, hole drilling, slotting, end facing, grinding and bonding. Outside the standard range, the same section is made as a part to drawing: see custom composite parts.

Request a quote

Where it is used

  • Equipment arm tube
  • Robot link and seventh axis
  • Drive shaft and roller shaft
  • Industrial equipment structural parts and brackets
  • Telescopic pole and tent pole
  • Audio and instrument tube

Stock sizes in detail

Read it as OD × wall. The ID is derived, not specified; one wall step at the same OD changes bending noticeably.

Code OD ID Wall Length Tolerance Note
RT-6-1.0 6 4 1.0 1000 ±0.1 Antenna pole
RT-7-1.0 7 5 1.0 1000 ±0.1 Tent pole
RT-8-1.0 8 6 1.0 1000 ±0.1 Kite spar
RT-8-0.125 8 7.75 0.125 1000 ±0.1 Thin-wall single ply
RT-10-1.0 10 8 1.0 1000 ±0.1 Telescopic pole
RT-10-0.5 10 9 0.5 1000 ±0.1 Thin-wall kit
RT-12-1.0 12 10 1.0 1000 ±0.1 Equipment arm tube
RT-12-0.5 12 11 0.5 1000 ±0.1 Thin-wall kit
RT-14-1.0 14 12 1.0 1000 ±0.1 Instrument tube
RT-15-1.5 15 12 1.5 1000 ±0.1 Link
RT-16-1.0 16 14 1.0 1000 ±0.1 Equipment arm tube
RT-18-1.0 18 16 1.0 1000 ±0.1 Bracket
RT-20-1.0 20 18 1.0 1000 ±0.1 Equipment arm tube
RT-22-1.0 22 20 1.0 1000 ±0.1 Camera pole
RT-25-1.5 25 22 1.5 1000 ±0.1 Robot link
RT-25-1.0 25 23 1.0 1000 ±0.1 Telescopic pole
RT-30-1.5 30 27 1.5 1000 ±0.1 Equipment arm tube
RT-40-1.5 40 37 1.5 1000 ±0.1 Robot seventh axis
RT-50-1.5 50 47 1.5 1000 ±0.1 Roller shaft
RT-60-1.5 60 57 1.5 1000 ±0.1 Roller shaft
RT-80-3.0 80 74 3.0 1000 ±0.1 Drive shaft
RT-100-3.0 100 94 3.0 1000 ±0.1 Roller
RT-120-4.0 120 112 4.0 1000 ±0.1 Robot arm
RT-150-5.0 150 140 5.0 1000 ±0.1 Large-diameter structure
RT-200-6.0 200 188 6.0 1000 ±0.1 Large-diameter structure
RT-250-7.0 250 236 7.0 1000 ±0.1 To drawing
RT-300-8.0 300 284 8.0 1000 ±0.1 To drawing
RT-400-10.0 400 380 10.0 1000 ±0.1 To drawing
RT-500-10.0 500 480 10.0 1000 ±0.1 To drawing

Layup direction sets stiffness, not the material

The same tube at OD 30 mm can be built as two entirely different parts. All 0° plies: stiffest on the axis, but a clamp will split it along the fibres. Add 90° hoop plies for reinforcement: crush resistance and internal pressure go up, at a small cost in axial stiffness. A tube dominated by ±45° plies has the best torsional stiffness — drive shafts and robot wrists use it. That is anisotropy: not a defect in itself, but a statement that the layup angle can be specified to follow your load path.

Wall thickness from 0.125 to 10 mm

0.125 mm is a single ply, for sleeved joints, models and light-duty covers. 1–3 mm is the range for standard structural parts. Above 5 mm the tube uses multi-cycle build-up and carries a faint spiral seam on the surface, that is the range for bearing housings. Roller shafts, pressure sleeves and large-diameter tube. A thick-wall tube is not automatically better — whatever exceeds the requirement is wasted weight and cost.

Telescopic tube: matched pairs, clearance held by grinding

Telescopic sections are made in pairs: the outer tube ground to ±0.05 mm. The inner tube matched to the clearance. 0.05–0.15 mm is the usual clearance — tighter seizes, looser rattles. For anti-rotation, make the inner tube hexagonal (see hexagonal carbon fibre tube), add a keyway. Cut a guide slot in the outer tube. Both tubes of a pair come from the same production batch, so diameter drift between batches cannot stop them fitting. Where the part has to take crushing or act as a pin, use a solid carbon fibre rod instead.

Surface: the weave is woven in, not printed on

The outer fabric decides the pattern you see. 3K/12K twill is the most common: what European customers call a woven finish. Plain weave is denser and flatter. A UD surface uses unidirectional cloth and gives an even matte black, which suits parts still to be painted. The weave is fixed by the outer fabric and post-machining cannot change it, so settle it when you order. All stock sizes can be supplied in 3K/12K twill, plain weave or UD.

Delivery states

  • Natural with clear coat Gloss, weave clearly visible; the carbon weave shows as soon as the part is fitted — the default for most visible parts.
  • Matte The same coating system, flattened; fewer fingerprints and reflections, common on equipment housings and exposed structural parts.
  • Painted The surface can be painted to customer requirement; colour and final gloss are set per project.
  • Laser engraving Customer logo, part number or graphic engraved on the surface.

Tolerance and inspection

OD (roll wrapped) ±0.1 mm Micrometer + dimensional report
OD (ground) ±0.05 mm OD micrometer
ID ±0.05 mm ID micrometer
Wall thickness ±5% (thin wall counted by plies) Calliper / ultrasonic
Length (cut to length) ±0.1 mm Water-jet guided / CNC
Straightness 0.5 mm / m Surface plate measurement
Slotting and hole position ±0.01 mm CMM

Common questions

Can you make parts to drawing?

Yes. Water-jet guided cutting to length, hole drilling and slotting, CNC milling and end facing are all done in-house. Where a metal end fitting or flange is required, we supply the assembly. We do not cut threads into carbon fibre — connections are bonded or flanged.

Roll wrapped or pultruded — which should I choose?

Roll wrapping lets you design the layup angle: good bending and torsion performance, no mould needed for thin wall, and a good fit where loads do not run in a single direction. Pultrusion puts all fibre on the axis: highest axial stiffness and a lower unit price, suited to pure axial load

What OD tolerance can you hold?

±0.1 mm on the roll-wrapped tube, ±0.05 mm after grinding, ±0.01 mm on slotting and hole positions. Sliding fits and bearing housings are quoted on ground tube

What are the MOQ and lead time?

500 pcs for standard diameters; trial batches by negotiation. Normal batches ship in 15–20 days, and 5–7 days where a new mandrel is needed

Can you make glass fibre?

Yes, in the same construction — lower stiffness and lower cost, common for insulating parts and low-frequency structures. Quoted through the glass fibre product line

What if two tubes will not fit together?

Telescopic pairs are made to clearance: the outer tube ground to ±0.05 mm, the inner tube matched. Say at order whether the joint is a sliding fit or a bonded fixed joint — 0.05–0.15 mm for sliding, an adhesive gap for bonding. The two tubes of a pair come from the same production batch; do not order them in separate batches

Send us the size

Section, length, quantity and service conditions — with these in hand the quote is accurate. Upload a drawing if you have one; without one, the same figures written out will do.

No file selected

PDF, DWG, DXF, STEP, STL, ZIP or a phone photo — up to 20 MB.

The part, the material, the size — or the problem it has to solve. Drawings and photos can go in the field above.

+ Company, quantity, timeline

Used only to answer this enquiry and for related technical follow-up.

  • Company address Zhuyuan Tianhuan International, No. 76 Keji 2nd Road, High-tech Zone, Xi'an, Shaanxi, China
  • Factory Fengjing Industrial Park, Middle Section of Fengwu East Road, Huyi District, Xi'an, Shaanxi, China
  • Sales email sales@atomfrp.com
  • Phone (WeChat) +86 18191567691 Email and forms answered 24/7; phone Mon–Fri 09:00–18:00 GMT+8
  • WhatsApp +853 68617664 Email and forms answered 24/7; phone Mon–Fri 09:00–18:00 GMT+8
  • A named engineer replies within 24 hours
  • NDA can be signed before any file is sent
  • Drawings and requirements are not disclosed

Send the drawing. We will send the route.

A drawing, a photo of a failed part, or three lines of requirement is enough to start. Scope, price indication and lead time within 24 hours.

No commitment · NDA available · Reply within 24 hours

Request a quote WhatsApp