Home Products Carbon fibre

Carbon fibre

Carbon fibre tube, square tube, sheet, solid rod and profiles — standard sizes come from the catalogue, anything outside it becomes a custom composite part. Take carbon when stiffness, weight and fatigue life decide the part; go to glass fibre when insulation or cost does.

Hexagonal carbon fibre tube

TubesCarbon fibre

Across flats 10–100 mm (hexagon and octagon), wall 1.0–10 mm (matched to A/F)

Pultrusion / roll wrapping / compression moulding

Tapered tube

TubesCarbon fibre

Large end 12–150 mm, small end 8–90 mm, taper 1:300 to 1:15

Roll wrapping / filament winding / compression moulding

Rigid carbon fibre sheet

PlatesCarbon fibre

Thickness 0.3–50 mm; full sheet 2440×1220 mm (4×8 ft)

Compression moulding (continuous fibre) / (chopped, forged finish); pultruded UD to drawing

Carbon fibre honeycomb sandwich panel

PlatesCarbon fibre

Overall thickness 6–30 mm; skin 0.5–1.5 mm (0.75 mm minimum below 8 mm overall); core 4–27 mm

Adhesive-film hot pressing, vacuum bagging, WCM wet compression moulding

Carbon fibre flat bar

ProfilesCarbon fibre

Width 5–50 mm, thickness 0.5–10 mm, section 2.5–500 mm² (width-to-thickness 2:1–100:1; outside that, square bar or sheet)

Pultrusion, unidirectional 0°

Carbon fibre angle

ProfilesCarbon fibre

Equal leg 10×10–100×100 mm (80 and above made to drawing), wall 1–10 mm

Pultrusion

Carbon fibre channel

ProfilesCarbon fibre

Channel depth 20–150 mm, flange width 10–75 mm, wall thickness 1.5–6 mm

Pultrusion

Carbon fibre I beam

ProfilesCarbon fibre

Section depth 30–200 mm, flange width 20–120 mm, wall thickness 2.5–8 mm

Pultrusion

Carbon fibre T profile

ProfilesCarbon fibre

Section depth 20–150 mm, flange width 20–100 mm, wall thickness 2–6 mm

Pultrusion

Not in the list?

Made to drawing

Send the drawing or the duty — we will say whether it can be made, and how.

Talk to us

Carbon is chosen for one reason: the part has to be lighter and still hold its shape. Below is where that reason holds, which process the part takes, and where carbon is the wrong answer.

When carbon is the right call

Three conditions, in this order: stiffness sets the section size, the weight sits on a moving part, or fatigue life is the limit. If none of the three holds, glass is cheaper and does the job — money spent on wall thickness goes further than money spent on fibre.

Which process the part takes

Three routes, decided by shape and volume rather than preference:

  • Roll wrapping — tube with fibre off the axis, carrying torsion and hoop load; OD 6–500 mm.
  • Pultrusion — constant section under axial load; straight, cheap, priced by the metre.
  • Moulding — anything that is not a constant section: brackets, housings, panels.

Where carbon is the wrong answer

Four cases where we say so before quoting:

  • Insulation is required — carbon conducts, and that is a material property, not something finishing fixes. Go to glass.
  • Cost leads and stiffness is not critical — glass with a thicker wall is the better spend.
  • Repeated impact or energy absorption — aramid or a hybrid lay-up suits better than carbon alone.
  • Long exposure to strong alkali or hydrofluoric acid — the standard resin system will not hold, and changing the fibre does not fix it.

Send the drawing. We will send the route.

A drawing, a photo of a failed part, or three lines of requirement is enough to start. Scope, price indication and lead time within 24 hours.

No commitment · NDA available · Reply within 24 hours

Request a quote WhatsApp