Overview

It does what steel angle does, without the rust. Frames, corner capping, angle bracing, stair nosing, cable tray brackets, wherever galvanised steel angle was used and the medium is acidic or alkaline. The part must not conduct, this replaces it. Density 2.0, a quarter of the weight of steel at the same section. A 6 m length of 50 × 50 comes in at a little over five kilos: one person carries it. The two legs meet at a right angle. Putting the profile against a corner gives you a 90° datum without a separate setting-out block. On a box corner the two legs land on two faces at once, with a row of bolts down each leg. The joint has one gap fewer and one alignment fewer than two flat plates mitred together. Equal leg from 25 to 150 mm, wall 3 to 12 mm, commonly in 6 m lengths. Equal angle covers general frames and bracing, unequal legs are made to drawing. The narrow leg against a panel, the wide leg carrying load, which saves both material and space. Load is carried by the section of the two legs rather than by piling on wall thickness. The centroid of an L sits out at the corner. The two directions do not have the same second moment of area: the load has to line up with the leg orientation. The same profile laid on its side carries much less. Draw the load direction on the selection sheet; it is more use than the leg length alone. Glass fibre is abrasive, so cutting, drilling and milling are all done in house. The water-jet guided laser also cuts to length and drills holes. It wears tooling faster than carbon fibre, and the extra tool consumption and slower cycle show up in the machining charge. A cut end exposes fibre, so parts for outdoor or damp service are sealed before dispatch. For a finished part rather than a length of stock, the route is custom composite parts.

Request a quote

Where it is used

  • Edge frames and trim: machine frame edges, box corner capping, panel edge closing, walkway edge strip
  • Platforms and access: stair nosing, platform edges, trench cover edge support
  • Supports and bracing: diagonal bracing, stiffening angles, brackets
  • Cable and tray: cable tray edge support, side panel fixing, trunking support
  • Chemical and sewage: railing, handrail, walkway support

Stock sizes in detail

kg/m is section area × density at 2.0 g/cm³; the section area is given alongside so you can check it.

Leg mm Wall mm Section mm² kg/m Typical use
25 × 25 3 141 0.28 Light frame, cover
30 × 30 3 171 0.34 Decorative frame, support
38 × 38 4 288 0.58 Frame, bracket
40 × 40 4 304 0.61 Edge frame, post
50 × 50 3 291 0.58 Edge support, railing
50 × 50 5 475 0.95 Load-bearing edge frame
50 × 50 6 564 1.13 Load-bearing bracket
51 × 51 6.35 607 1.21 Joint facing piece
60 × 60 6 684 1.37 Platform edge beam
60 × 60 8 896 1.79 Main edge beam
75 × 75 6 864 1.73 Long-span edge frame
75 × 75 10 1400 2.80 Load-bearing edge beam
100 × 100 8 1536 3.07 Main structural bracing
100 × 100 10 1900 3.80 Heavy-duty bracing
150 × 150 12 3456 6.91 Heavy-duty post
100 × 50 (unequal) 8 1136 2.27 Single-side load-bearing edge frame

Edge trim, corner capping, bracing: where an angle sits

Edge trim. Corner capping and bracing is where an L profile belongs in a structure. Trim wraps a panel edge, hiding the cut and adding stiffness. Corner capping takes the corners of a box or a cabinet. Bracing does the diagonals and the stiffening, against box section. A box tube is closed on four sides and resists torsion. It will not sit into a corner. It needs a connection plate made up for it. An angle opens to take exactly one right angle, and one part does the corner, against flat bar. Flat bar covers one face only, so a corner needs two pieces and two fixings. One angle does the job of both, and locates itself. For light guardrail, machine guarding and walkway edge strip, an angle uses less material than box section. The load is at the edge anyway. The middle of a box is doing nothing.

Equal or unequal leg

Equal legs are symmetric, so the joint is symmetric and the part cannot go on the wrong way round. One stock item covers the job. General frames, bracing and corner capping all use it, unequal legs divide the work. The narrow leg bears on a panel as edge trim while the wide leg carries load, or the other way round. Wide leg as a foot, narrow leg as a stop. Grating edge support, panel closing and cable tray side fixing all go this way. Unequal is made to drawing, with both leg sizes and the wall given together. "L profile" on its own cannot be made.

Joints: hole position, edge distance, inside corner

Holes through a leg are sized on bearing, not on tensile. Start with an edge distance of three hole diameters, four is safer, and leave three diameters or more between holes. Glass bearing strength is a fraction of axial tensile, so a narrow edge tears when the bolt is tightened. The inside corner is round, not sharp, with the radius following the wall. A part that has to sit into a square corner needs clearance for that radius, do not draw it against a sharp corner. The junction of the two legs is where the fibre is thickest and where stress concentrates. Keep bolts on the centre line of a leg, away from the junction. For a lengthened run, scarf the joint rather than butting square ends together. A square butt relies entirely on the bolts in shear, which is the weakest direction in glass. A scarf spreads the load into a bonded face and is far steadier. Where metal meets glass, watch galvanic corrosion. The glass itself insulates, so use an insulating washer or matching metals, and do not let stainless steel bite directly into aluminium.

Anti-slip grit finish and colour

Walkway edge strip, stair nosing, platform edges, anywhere a foot lands, take the grit finish. The grit is embedded in the surface resin during pultrusion, not sprayed on afterwards, so it does not wear off. Grit goes on the outside of one leg only; the other leg stays smooth for bonding. Say at order which leg takes the grit, decided by the leg orientation rather than by which is up. Colour is pigmented into the resin, grey, yellow, green and black are common, and the cut face matches. Grit covers the colour, so grit-finish parts are usually made dark.

Post-machining: done in house, arrives as a part

Lengths are cut to drawing, the water-jet guided laser cuts to length and drills holes. CNC mills notches, slots and end chamfers, the grit goes on the specified leg. Anything needing sealing is sealed before dispatch. It arrives as a part and goes straight into assembly, cutting. The water-jet guided laser cuts to length and drills holes, with no burning and no breakout, length ±0.1 mm. Sawn to ±2 mm, CNC-milled edge ±0.2 mm, holes and slots. Hole position ±0.01 mm; notches, slots and end chamfers to drawing. Edge distance from three hole diameters, four is safer, glass bearing strength is low, and a short edge tears when the bolt is tightened. Check it at layout, ends. A cut end exposes fibre and water travels along it. Parts for outdoor, damp or chemical service are sealed in house, with resin of the same system or an end cap, threads. The profile is not tapped directly, because interlaminar shear will not hold a thread. Threaded parts take an insert or a through bolt, fitted in house. Glass fibre wears tooling faster than carbon fibre, and both tool consumption and cycle time are higher. That shows up in the machining charge, not in the tolerance. All of this is done on our own profiles only, customer-supplied finished parts are not machined. Customer-supplied fibre or prepreg is processed into product.

Delivery states

  • Full length Supplied at standard length, protective film intact
  • Cut to length Cut to drawing, ±2 mm
  • Laser cut Water-jet guided laser for cut-to-length and holes, ±0.1 mm
  • Precision cut CNC-milled edge, ±0.2 mm
  • Drilled and slotted To drawing, hole position ±0.01 mm
  • Ends Sawn edge / CNC chamfer / sealed end
  • Grit finish Anti-slip grit on the specified leg, supplied with the batch
  • Assembly Combined with metal parts and inserts, batch after first-article approval

Tolerance and inspection

Leg ±0.5%, minimum ±0.2 mm, maximum ±0.75 mm The minimum applies to small sections, the percentage to large ones
Wall, 3 mm band ±0.20 mm Thin leg, jointed with through bolts and washers
Wall, 5 mm band ±0.35 mm The usual load-bearing bracing
Wall, 10 mm band ±0.45 mm Heavy structure
Wall 6 / 8 / 12 mm 6 mm takes the 5 mm band; 8 mm and 12 mm take the 10 mm band No separate tolerance between bands
Right angle 90° ±1.5° Corner capping fit
Inside radius Follows the wall, of the same order Leave clearance for it on facing parts
Straightness 1.5 mm/m Accumulates with length on long spans
Twist Leg ≤75 mm: 1.5°/m; >75 mm: 1.0°/m Wide legs twist more readily
Sawn length +50 / −0 mm Blank, with machining allowance
Water-jet guided laser ±0.1 mm Cut-to-length and holes
Hole position ±0.01 mm To drawing
CNC-milled edge ±0.2 mm Delivered this way on precision parts

Common questions

L profile or box section — which should I choose?

Load at the edge and a corner to sit into: the angle. Closed on four sides and torsion to resist: box section. For light guardrail and walkway edge strip, an angle uses less material.

Equal or unequal leg?

Equal for general work: it cannot go on the wrong way round and one stock item covers it. Unequal where one leg bears on a panel and the other carries load — narrow leg as trim. Load at the edge and a corner to sit into: the angle. Closed on four sides and torsion to resist: box section. For light guardrail and walkway edge strip, an angle uses less material

What is the leg tolerance?

±0.5%, minimum ±0.2 mm, maximum ±0.75 mm

What is the wall tolerance?

By band: 3 mm band ±0.20, 5 mm band ±0.35, 10 mm band ±0.45, 6 mm takes the 5 mm band. 8 mm and 12 mm take the 10 mm band

How true is the right angle?

90° ±1.5°. Corner capping has to allow for that tolerance — do not draw it to a theoretical square with zero clearance

Is the inside corner sharp or round?

Round, with the radius following the wall, of the same order. A part going into a square corner needs clearance for that radius at drawing stage

Can you drill and slot it?

Yes, in house. Hole position ±0.01 mm, edge distance from three hole diameters, and three diameters or more between holes. Slots, notches and chamfers all to drawing

Can you do an anti-slip grit finish?

Yes. The grit is embedded in the surface resin during pultrusion and does not wear off. It goes on the specified leg only, so the other leg stays smooth for bonding

Can it be laser cut?

Yes. Water-jet guided laser cuts to length and drills holes without burning or breakout: length ±0.1 mm, hole position ±0.01 mm

Do the ends need treatment?

Yes for outdoor, damp or chemical service, and we seal them in house with resin of the same system or an end cap

Can I choose the colour?

Pigmented in the resin — grey, green, yellow and black are common, and the cut face matches, grit-finish parts are usually dark

Can unequal leg be customised?

Yes, both leg sizes and the wall to drawing, with the smallest leg limited by bending. "L profile" alone is not enough; give both legs and the wall

What does post-machining cover?

Water-jet guided cutting, CNC milling, drilling, slotting, end chamfers, grit finish and end sealing, all in house. A drawing or a DXF is enough

How long is a length, and what is the MOQ?

6 m as standard, and cut to the length you need. Full lengths are the minimum; cut lengths are quoted per piece, and drilled or slotted parts per piece

Send us the size

Section, length, quantity and service conditions — with these in hand the quote is accurate. Upload a drawing if you have one; without one, the same figures written out will do.

No file selected

PDF, DWG, DXF, STEP, STL, ZIP or a phone photo — up to 20 MB.

The part, the material, the size — or the problem it has to solve. Drawings and photos can go in the field above.

+ Company, quantity, timeline

Used only to answer this enquiry and for related technical follow-up.

  • Company address Zhuyuan Tianhuan International, No. 76 Keji 2nd Road, High-tech Zone, Xi'an, Shaanxi, China
  • Factory Fengjing Industrial Park, Middle Section of Fengwu East Road, Huyi District, Xi'an, Shaanxi, China
  • Sales email sales@atomfrp.com
  • Phone (WeChat) +86 18191567691 Email and forms answered 24/7; phone Mon–Fri 09:00–18:00 GMT+8
  • WhatsApp +853 68617664 Email and forms answered 24/7; phone Mon–Fri 09:00–18:00 GMT+8
  • A named engineer replies within 24 hours
  • NDA can be signed before any file is sent
  • Drawings and requirements are not disclosed

Send the drawing. We will send the route.

A drawing, a photo of a failed part, or three lines of requirement is enough to start. Scope, price indication and lead time within 24 hours.

No commitment · NDA available · Reply within 24 hours

Request a quote WhatsApp