Home Products Glass fibre and GRP sections

Glass fibre and GRP sections

Glass fibre and GRP tube, square tube, sheet and profiles — normal batches ship in 15–20 days. Insulating parts, and parts made to drawing, take the custom composite parts route. Same workshop, same team; only the fibre and the resin change.

GRP tube

TubesGlass fibre

Stock range: outside diameter 4–150 mm, wall 1–6 mm

Pultrusion as standard, winding for large diameters, roll wrapping for thin-wall small batches

Fibreglass sheet

PlatesGlass fibre

Thickness 0.5–50 mm; full sheet 1220×2440 mm or 1020×1220 mm

Hot-pressed lamination; continuous lamination for thin sheet, compression moulding for thick

GRP rod

RodsGlass fibre

Ø3–150 mm standard, larger to drawing

Pultrusion; ground on request

GRP angle

ProfilesGlass fibre

Equal leg 25–150 mm, wall 3–12 mm; unequal leg to drawing

Pultrusion

GRP channel

ProfilesGlass fibre

Height 50–200 mm, width 25–75 mm, wall 3–12 mm

Pultrusion

GRP I beam

ProfilesGlass fibre

Depth 60–300 mm, flange 30–150 mm, wall 4–12 mm

Pultrusion

Not in the list?

Made to drawing

Send the drawing or the duty — we will say whether it can be made, and how.

Talk to us

Below: when glass fibre is the right call, and when it is not. That tells you more than a spec table.

Small-bore tube, roughly 10–90 mm OD, goes into guardrail, ladder, tent-pole and insulating-pole work — by the piece or by the metre, cut and drilled to drawing.

When glass fibre, and when not

Glass fibre is not the cheap option. It is the option when one constraint in the part rules carbon out, most often that constraint is electrical, money comes second. Less than expected. Move a part from carbon to glass and the extra wall thickness needed to restore stiffness eats part of the saving. The order to judge in: insulation first, stiffness second, cost last.

Glass fibre Carbon fibre Aluminium
Stiffness (same weight) moderate high low
Electrical insulating, high volume resistivity conductive conductive
Corrosion good, except strong alkalis and hydrofluoric acid good, but galvanic corrosion where it meets metal fair, needs surface treatment
Impact moderate to good — tougher than carbon, not as good as metal low, brittle good, absorbs by deformation
Unit cost low high lowest

Steel does not get a column: cheap, heavy, rusts, and no advantage beyond cost. Compare it against the same three rows.

Glass fibre's place is clear: not the best material, the right one when there are the most constraints.

The line that gets its own page

Live-working booms, poles and ladders; insulating housings for equipment and robots. This line has its own page because the test differs. An insulating part is judged on whether any path runs from the live part to earth. Material data does not answer it.

Antistatic housings are not on this line. They belong to the conductive family — carbon filler or conductive coating — which is the opposite design goal. The same workshop can make both, but the material, the drawing and the acceptance test all change.

Where glass fibre is the wrong answer

  • Extreme stiffness, weight saved to the gram — that is carbon's job; glass does not close the gap.
  • Heat conduction or heat dissipation — glass fibre is a poor conductor of heat.
  • Long exposure to strong alkali or hydrofluoric acid — standard glass fibre is attacked.
  • Repeated impact, energy absorption — aramid, or a hybrid lay-up, suits better than glass alone.
  • No surface finishing — the part still works, but outdoors the difference shows in two or three years.

Questions we get on this

Can GRP be used for electrical insulation?

Yes, the material does not conduct. The part has to be designed as an insulator: no uninsulated metal path from the live part to earth, and every cut edge sealed. Material choice alone does not make a part insulating.

What is the lead time for glass fibre sections?

Normal batches ship in 15–20 days. Large volumes are quoted against the schedule the volume needs. A new mould adds 5–7 days for the tooling, counted from drawing sign-off.

Can you machine GRP after pultrusion?

Yes, cutting to length, drilling, milling and threading are all done in house, two things change the answer. Glass fibre blunts tooling faster than aluminium, and every machined face has to be sealed. The exposed cut is the weakest point in a corrosive or electrical application.

Can glass and carbon go into the same part?

Yes, but be clear why. The usual pattern is carbon where stiffness is needed locally, glass elsewhere, the cost sits at the joint, carbon is conductive. Any metal fastener or insert touching it becomes a galvanic couple and has to be isolated. The two materials also expand differently, so the interface is designed rather than just bonded.

Does it age outdoors?

The fibre does not mind the sun; the resin does. UV chalks the resin surface and moisture uptake pulls the properties down. The fix is the right resin, a proper finish and sealed cut edges rather than a thicker wall.

Send the drawing. We will send the route.

A drawing, a photo of a failed part, or three lines of requirement is enough to start. Scope, price indication and lead time within 24 hours.

No commitment · NDA available · Reply within 24 hours

Request a quote WhatsApp