Overview

For bending strength at low weight, choose a tube. For crush resistance, shear, drilling, pinning or being clamped, choose a solid rod. It has no sidewall that can collapse. Putting a tube where a rod belongs is usually not a strength failure but a local crush: a clamp flattens it. A pin hole cracks under load. Cut lengths come from here. A machined part comes from custom composite parts.

Request a quote

Where it is used

  • Cable racks and guardrail posts: Ø3–10 mm rods, cut and drilled to length
  • Live-line operating rods and insulating rods: Ø10–50 mm, low-absorption resin, sealed ends
  • Arrester core rods (to drawing), structural supports, equipment posts, ladder rails
  • Pins, guide rails and parts with a fit requirement: ground to ±0.05 mm

Stock sizes in detail

Normal batches ship in 15–20 calendar days from drawing approval and receipt of deposit.

Diameter mm Tolerance Usual length Process Typical use
3–10 ±0.15 mm 1 / 2 m pultruded cable racks, guardrail posts, low-voltage insulating rods
over 10 to 50 ±0.20 mm 2 / 3 m pultruded structural supports, equipment posts, live-line operating rods
over 50 to 150 ±0.30 mm 3 / 6 m pultruded large-diameter supports, ladder rails
3–50 ground ±0.05 mm to drawing pultruded + ground pins, guide rails, parts with a fit requirement

Pultrusion puts every fibre on the axis Roving comes off the creel, through the resin bath, into the heated die, cures, is pulled and cut. Every fibre runs along the length, axial bending and tension are strong; transverse and torsional loads have almost no fibre to carry them. That is a trade-off rather than a defect. If a part has to resist torsion, a rod is the wrong choice.

For insulation, the whole rod has to be free of flaws Glass fibre does not conduct. Is why live-line operating rods and cable racks are made from it. But a non-conductive material does not make a non-conductive part: cut ends, drilled holes and scratches are weak points on the insulation path. Resin is matched to the duty, the section must be free of voids and dry fibre, and most cut ends are sealed. We do not quote voltage ratings. Those numbers come from whole-part testing, not from material data.

Delivery states

  • Natural (die face) Cream to pale green, smooth; ready to bond
  • Veil-faced Matte, resin-rich surface for UV and chemical exposure
  • Pigmented Yellow or black in the resin, not painted on
  • Ground ±0.05 mm, for fits and guide rails

Tolerance and inspection

Diameter ±0.15 / ±0.20 / ±0.30 mm Micrometer, by band
Diameter (ground) ±0.05 mm Micrometer after grinding
Length up to 2 m ±0.1 mm At 20 °C
Length over 2 m ±0.5 mm At 20 °C
Straightness 1 mm/m Dial gauge on a surface plate

Common questions

Glass fibre rod or carbon fibre rod, how do I choose?

Two questions: insulation, and torsion, need insulation, glass fibre. Need torque resistance, or extreme light-and-stiff, carbon fibre, the price differs several times over

How tight can the diameter tolerance be?

Banded as in the table; grinding gets it to ±0.05 mm (quoted separately). For parts with a fit requirement, put the tolerance on the drawing. We quote to the drawing, not to a catalogue item

Can you cut to length?

Yes, cutting is in-house and the ends are sealed after cutting. Length tolerance is ±0.1 mm up to 2 m and ±0.5 mm over 2 m, both measured at 20 °C

Will it age outdoors?

The fibre does not mind sun; the resin does. UV chalks the resin and water absorption degrades performance. The answer is the right resin and proper surface and end sealing rather than a bigger diameter

Can you do non-standard colours?

Yes. Natural, yellow and black are the three we run routinely. Other colours are matched to a colour card, with MOQ and lead time quoted separately

Send us the size

Section, length, quantity and service conditions — with these in hand the quote is accurate. Upload a drawing if you have one; without one, the same figures written out will do.

No file selected

PDF, DWG, DXF, STEP, STL, ZIP or a phone photo — up to 20 MB.

The part, the material, the size — or the problem it has to solve. Drawings and photos can go in the field above.

+ Company, quantity, timeline

Used only to answer this enquiry and for related technical follow-up.

  • Company address Zhuyuan Tianhuan International, No. 76 Keji 2nd Road, High-tech Zone, Xi'an, Shaanxi, China
  • Factory Fengjing Industrial Park, Middle Section of Fengwu East Road, Huyi District, Xi'an, Shaanxi, China
  • Sales email sales@atomfrp.com
  • Phone (WeChat) +86 18191567691 Email and forms answered 24/7; phone Mon–Fri 09:00–18:00 GMT+8
  • WhatsApp +853 68617664 Email and forms answered 24/7; phone Mon–Fri 09:00–18:00 GMT+8
  • A named engineer replies within 24 hours
  • NDA can be signed before any file is sent
  • Drawings and requirements are not disclosed

Send the drawing. We will send the route.

A drawing, a photo of a failed part, or three lines of requirement is enough to start. Scope, price indication and lead time within 24 hours.

No commitment · NDA available · Reply within 24 hours

Request a quote WhatsApp